Filter

Filters

35 devices found

Application Group
Applications

Devices

– Global positioning system tag – communicates with GPS satellites to establish position with high accuracy, but only when the tag or animal is on land or at the water surface – Fastloc Global positioning system tag – GPS tag for aquatic animals that surface or haul out, when the tag locks onto the GPS satellite network to establish position with high accuracy – Pop-up satellite archival tag – after some period of time recording sensor data, the tag detaches itself from the animal and floats to the surface where it uses satellite connectivity to uplink the data stored on the tag – Acoustic tag – attached to the animals being tracked emit acoustic signals (typically ultrasound) which travel through water much better than RF signals. These signals are then received by buoys, which can then use satellite communications to backhaul the data to where it’s needed.

Camera types used on agrobots: – RGB cameras – extensively used in agricultural machine vision applications for fruit/plant detection, yield prediction, segmentation tasks, disease detection, ripeness detection, weed detection and insects detection – Hyperspectral, thermal, or ultrasonic cameras – typically provide better results than conventional RGB color images – Stereoscopic cameras – provides 3D plant structure information (dimension of crops (depth information, crop height, leaf shape, leaf area etc.)) Critical factor is the camera’s resolution, which should be high enough to capture the details of the scene especially in the cases of insect and disease detection.

Fiber-optic Distributed Temperature Sensing (DTS) systems and pressure gauges enable critical monitoring during exploration and energy production for Enhanced Geothermal Systems (EGS). These sensors can be used to: – Estimate production potential in or between new wells by measuring the distributed temperature and the point pressure, or pressure measured at the bottom of the well. These measurements allow the calculation of reservoir size, flow resistance between wells (if multiple wells are instrumented), well bore damage caused by drilling, effectiveness of the fracturing operations, and well completion. – Monitor surface and subsurface scale buildup and chemical clean-up. Scale, a mineral residue precipitated from geothermal fluid in response to changes in water pressure and temperature, builds up on pipe walls and will, over time, form a thick, insulating layer that limits flow and may block a pipe. Chemicals are injected into the pipe to remove the accumulated scale. By understanding severity of the scaling, operators can better consider what mitigation options are most suitable as well as minimize the use of expensive chemicals. – Provide permanent monitoring of injector and producer wells to allow identification of the specific zones and fractures that produce fluids. – Perform integrity monitoring for casing and tubing leaks to avoid contaminating ground water and subsurface aquifers.

Rain Gauges: Modern rain gauges often come equipped with wireless communication capabilities, allowing them to transmit data on rainfall amounts to monitoring centers in real time. Stream Gauges: Many stream gauges are designed to wirelessly transmit data on water levels and flow rates, providing crucial information for flood forecasting.Soil Moisture Sensors: These sensors can be equipped with wireless communication to send soil moisture data to a central system, which helps in assessing the risk of flooding, especially in areas prone to flash floods. Pressure Transducers: Used in various water bodies, these sensors can wirelessly transmit water pressure data, which is then used to calculate water levels. Ultrasonic Sensors: These can be set up to measure water levels and then transmit the data wirelessly to a central monitoring system. Anemometers: Modern anemometers can send wind data wirelessly to meteorological centers, contributing to broader weather pattern analysis for flood prediction. Tide Gauges: In coastal areas, tide gauges equipped with wireless communication capabilities transmit sea level data, which is crucial for predicting storm surges and coastal floods.

Some of the key types of sensors used in urban air quality monitoring include: Particulate Matter (PM) Sensors: These sensors measure concentrations of particulate matter Nitrogen Dioxide (NO2) Sensors: NO2 is a common urban pollutant, often produced by vehicle exhaust and industrial processes. Sulfur Dioxide (SO2) Sensors: Commonly produced by industrial processes, SO2 levels are often monitored using ultraviolet fluorescence or electrochemical sensors. Ozone (O3) Sensors: Ozone at ground level is a harmful pollutant, and its concentration is typically monitored using ultraviolet (UV) photometry or electrochemical cells. Carbon Monoxide (CO) Sensors: CO is a colorless, odorless gas resulting from incomplete combustion. It’s usually monitored in urban environments using electrochemical sensors. Volatile Organic Compounds (VOCs) Sensors: VOCs are emitted from a variety of sources, including vehicle exhaust, industrial processes, and consumer products. Meteorological Sensors: These sensors measure environmental conditions like temperature, humidity, wind speed, and wind direction, which are important for understanding and interpreting air quality data.

Wireless Z-Traps are devices used to catch pests around the plants using pheromone lure. Pest count information is wirelessly passed along from up to 1 km away using a base station to the online cloud service. This information is used to study and determine where and how much pesticides will be required. Imagery sensors capture imagery data to identify the diseases in plants – RGB sensors – have three colour channels, i.e., red, green and blue, which can be used to perceive the biometric effect in the plants – fluorescence Imagery sensors – used to distinguish the photosynthetic activities in the plants – spectral sensors – capture images containing the spatial information of objects in multiple wavebands, used to analyse crops’ health and pest attack – thermal sensors – used to measure the water status in the plant by measuring the temperature Weather condition monitoring sensors, i.e., temperature, dew, humidity and wind speed, are used to monitor weather parameters to find a correlation between pest growth with weather