Animals are fitted with sensor-equipped collars that collect information regarding their location, direction, and average speed (geolocation, acceleration, gyro sensors)
Cameras for mines and tunnels are an essential element of security and safety monitoring. The mining sector presents a number of challenges, from low lighting to connectivity issues in remote areas. These surveillance cameras observe the many processes within the mine and are mostly installed in a permanent, overt manner, with portable covert cameras being used on a temporary basis. IR thermal imaging cameras are often used as they offer the ability to see in dark, foggy or dust filled environments where there are large trucks, cranes, robotics and other moving apparatus that present danger to humans.
Car-embedded sensors (lidar and radar), GNSS, and potentially data from brakes, accelerator, steering wheel, etc.
Driverless vehicles and Autonomous Drilling Systems that can operate without human intervention allow operations around the clock, enabling minerals to be extracted and processed in shorter time-frames. Real-Time Kinematic GPS (RTK-GPS) is used In underground mines due to a limited range of signal transmission below the surface and lack of satellite coverage in depth. RTK-GPS is used to ensure autonomous vehicles and drilling systems have clear path-tracking and collision avoidance capabilities. GPS-guided drilling operations. GPS provides accurate information to the drill head to control its direction deep within the earth.
Drones equipped with mobile communication link for C&C between the vehicle and a ground control station
Fiber-optic Distributed Temperature Sensing (DTS) systems and pressure gauges enable critical monitoring during exploration and energy production for Enhanced Geothermal Systems (EGS). These sensors can be used to: – Estimate production potential in or between new wells by measuring the distributed temperature and the point pressure, or pressure measured at the bottom of the well. These measurements allow the calculation of reservoir size, flow resistance between wells (if multiple wells are instrumented), well bore damage caused by drilling, effectiveness of the fracturing operations, and well completion. – Monitor surface and subsurface scale buildup and chemical clean-up. Scale, a mineral residue precipitated from geothermal fluid in response to changes in water pressure and temperature, builds up on pipe walls and will, over time, form a thick, insulating layer that limits flow and may block a pipe. Chemicals are injected into the pipe to remove the accumulated scale. By understanding severity of the scaling, operators can better consider what mitigation options are most suitable as well as minimize the use of expensive chemicals. – Provide permanent monitoring of injector and producer wells to allow identification of the specific zones and fractures that produce fluids. – Perform integrity monitoring for casing and tubing leaks to avoid contaminating ground water and subsurface aquifers.
For habitat environment observation, monitoring sensors such as temperature, humidity, height, wind, light, and cameras are used
If a speaker has been installed in the UAV, voice messages from the disaster coordination base can be delivered to disaster victims via the cellular network, while the voice of victims can be picked up using the microphone mounted on the UA, and relayed back to the disaster coordination base.
Mobile-enabled IoT sensors, Bluetooth beacons, infrared counters or sensors embedded in the pavement, turnstiles
Portable waste bin or portable toilets enabled with GNSS. Once data related to fill rates and temperatures of smart bins /toilets are collected, the sensors relay the exact location and other waste related information of the bins in question so waste management can send out SMSes to nearby garbage collectors to do the needed collection/emptying before harmful carbon emissions are released.
Sensor information (e.g., LIDAR, RADARs), vehicle Status (e.g., speed) and video streaming images (e.g., two cameras (front, end))
Sensors based on radar, visual or infrared technology integrated into the road infrastructure. The sensors detect approaching road users and signal this to the road users by visual and audio warnings.
Smart meters that collect granular real-time data across the water grid, LED light sensors to monitor water levels in tanks, pH sensors, temperature sensors and turbidity sensors in pipelines and storage and distribution tanks, volume sensor
Smart Waste Bin with wireless ultrasonic fill-level sensors and other indicators such as temperature and tilt within waste container
To sense the environment, AVs use a combination of sensors:・External sensors (GNSS, cameras, lidars etc)・Internal automotive sensors and actuators (brakes, steering wheel, accelerator, etc)
Underground mining has significant safety hazards due to high-stress concentrations, weak rock masses, and limited access and air quality. Different sensors are used in mine-related activities, such as geophones in exploration and blast control, piezometers in dewatering and toxic gas detectors in working frontlines.
Vibration sensors such as low-frequency accelerometers are mounted on the casing of the turbine and generator near the bearings and shaft. Water quality sensors (Dissolved Oxygen (DO) Sensor)
