Body-worn sensors to track the health (heart rate, respirations, EKG, body temperature) and location of responders Additional Body Worn Sensors to detect a bullet impacting an officer’s vest; detect the absence of movement that might indicate a crisis condition. Sensors that will track the amount of air in a firefighters SCBA tank
Bomb disposal robot equipped with video cameras and chemical, biological, and nuclear sensors for detection of explosive materials.
Cameras for mines and tunnels are an essential element of security and safety monitoring. The mining sector presents a number of challenges, from low lighting to connectivity issues in remote areas. These surveillance cameras observe the many processes within the mine and are mostly installed in a permanent, overt manner, with portable covert cameras being used on a temporary basis. IR thermal imaging cameras are often used as they offer the ability to see in dark, foggy or dust filled environments where there are large trucks, cranes, robotics and other moving apparatus that present danger to humans.
Cameras for Monitoring of parking lot’s occupancy in real time. Image data from the cameras connected to a Gateway directly sent to the management system of a parking lot
Car-embedded sensors (lidar and radar), GNSS, and potentially data from brakes, accelerator, steering wheel, etc.
Driverless vehicles and Autonomous Drilling Systems that can operate without human intervention allow operations around the clock, enabling minerals to be extracted and processed in shorter time-frames. Real-Time Kinematic GPS (RTK-GPS) is used In underground mines due to a limited range of signal transmission below the surface and lack of satellite coverage in depth. RTK-GPS is used to ensure autonomous vehicles and drilling systems have clear path-tracking and collision avoidance capabilities. GPS-guided drilling operations. GPS provides accurate information to the drill head to control its direction deep within the earth.
Drones equipped with mobile communication link for C&C between the vehicle and a ground control station
Fiber-optic Distributed Temperature Sensing (DTS) systems and pressure gauges enable critical monitoring during exploration and energy production for Enhanced Geothermal Systems (EGS). These sensors can be used to: – Estimate production potential in or between new wells by measuring the distributed temperature and the point pressure, or pressure measured at the bottom of the well. These measurements allow the calculation of reservoir size, flow resistance between wells (if multiple wells are instrumented), well bore damage caused by drilling, effectiveness of the fracturing operations, and well completion. – Monitor surface and subsurface scale buildup and chemical clean-up. Scale, a mineral residue precipitated from geothermal fluid in response to changes in water pressure and temperature, builds up on pipe walls and will, over time, form a thick, insulating layer that limits flow and may block a pipe. Chemicals are injected into the pipe to remove the accumulated scale. By understanding severity of the scaling, operators can better consider what mitigation options are most suitable as well as minimize the use of expensive chemicals. – Provide permanent monitoring of injector and producer wells to allow identification of the specific zones and fractures that produce fluids. – Perform integrity monitoring for casing and tubing leaks to avoid contaminating ground water and subsurface aquifers.
High definition Video Camera, pop-up / remote production facilities with virtualized edge production software,with wireless bridge to deliver multiple camera signals back for broadcast content delivery.
If a speaker has been installed in the UAV, voice messages from the disaster coordination base can be delivered to disaster victims via the cellular network, while the voice of victims can be picked up using the microphone mounted on the UA, and relayed back to the disaster coordination base.
Medical grade wearables: Wearable device worn or placed on a body part to record a particular physiological change (e.g., respiratory rate sensors or blood pressure monitors). Any biosensor device for recording data from biological or chemical reactions (e.g., pulse oximeters or spirometers).
Robotic assisted surgical device. On the remote expert/surgeon side, these applications may require a VR interface in order to provide an immersive sense of experience.
Seismic sensors used for monitoring of seismic activity in geothermal plants can enhance the safety aspect of power generation. Geothermal power plants are generally located near earthquake-prone zones and the ability to manage such power plants remotely is useful for employee safety. Vibration and temperature sensors are used in turbines and generators to monitor temperatures and detect vibrations.
Sensor information (e.g., LIDAR, RADARs), vehicle Status (e.g., speed) and video streaming images (e.g., two cameras (front, end))
Sensors based on radar, visual or infrared technology integrated into the road infrastructure. The sensors detect approaching road users and signal this to the road users by visual and audio warnings.
Vibration sensors such as low-frequency accelerometers are mounted on the casing of the turbine and generator near the bearings and shaft. Water quality sensors (Dissolved Oxygen (DO) Sensor)
