Body-worn sensors to track the health (heart rate, respirations, EKG, body temperature) and location of responders Additional Body Worn Sensors to detect a bullet impacting an officer’s vest; detect the absence of movement that might indicate a crisis condition. Sensors that will track the amount of air in a firefighters SCBA tank
Conductivity, Temperature, and Depth (CTD) Sensors: These are widely used in oceanography. CTD sensors measure conductivity (to infer salinity), temperature, and depth simultaneously, providing comprehensive data essential for climate change studies.
Digital Temperature Sensors: Placed in various parts of a rainforest, these sensors can provide detailed temperature data, helping to detect and analyze sudden temperature variations.
Drones equipped with mobile communication link for C&C between the vehicle and a ground control station
Fiber-optic Distributed Temperature Sensing (DTS) systems and pressure gauges enable critical monitoring during exploration and energy production for Enhanced Geothermal Systems (EGS). These sensors can be used to: – Estimate production potential in or between new wells by measuring the distributed temperature and the point pressure, or pressure measured at the bottom of the well. These measurements allow the calculation of reservoir size, flow resistance between wells (if multiple wells are instrumented), well bore damage caused by drilling, effectiveness of the fracturing operations, and well completion. – Monitor surface and subsurface scale buildup and chemical clean-up. Scale, a mineral residue precipitated from geothermal fluid in response to changes in water pressure and temperature, builds up on pipe walls and will, over time, form a thick, insulating layer that limits flow and may block a pipe. Chemicals are injected into the pipe to remove the accumulated scale. By understanding severity of the scaling, operators can better consider what mitigation options are most suitable as well as minimize the use of expensive chemicals. – Provide permanent monitoring of injector and producer wells to allow identification of the specific zones and fractures that produce fluids. – Perform integrity monitoring for casing and tubing leaks to avoid contaminating ground water and subsurface aquifers.
High definition Video Camera, pop-up / remote production facilities with virtualized edge production software,with wireless bridge to deliver multiple camera signals back for broadcast content delivery.
Infrared Thermal Imaging: Used to map urban heat islands from a distance, often from airborne platforms or satellites. Networks of Digital Temperature Sensors: Deployed across different urban areas, these sensors can provide granular temperature data, highlighting variations within a city. Weather Stations: Often used in urban settings, weather stations can provide comprehensive environmental data, including temperature, which is crucial for studying urban heat island effects.
Monitoring emissions from factories in real-time involves a variety of sensors and instruments designed to measure different types of pollutants. These sensors are often networked together and connected to a central monitoring system that collects, analyzes, and reports data in real time. This enables factory operators and regulatory agencies to track emissions continuously and ensure compliance with environmental regulations, as well as to make informed decisions about emission control and reduction strategies. Gas Analyzers: These sensors are used to detect and quantify specific gases in the air, such as carbon dioxide (CO2), sulfur dioxide (SO2), nitrogen oxides (NOx), and volatile organic compounds (VOCs). Particulate Matter (PM) Sensors: These sensors measure the concentration of particulate matter in the air. Opacity Monitors: These are used to measure the opacity of emissions from smokestacks, which is an indicator of particulate matter concentrations. Flame Ionization Detectors (FID): FIDs are used to measure total hydrocarbon levels in emissions. FTIR (Fourier Transform Infrared Spectroscopy) Analyzers: These analyzers can detect a wide range of gases and are particularly useful for identifying complex mixtures of pollutants. UV Spectrometers: Ultraviolet spectrometry can be used to measure specific gases like ozone (O3) and sulfur dioxide (SO2) based on their absorption characteristics in the UV range. Chemical Sensors and Biosensors: These are used to detect and measure specific chemical compounds in emissions. Temperature, Pressure, and Flow Sensors: These sensors provide additional data on the emission conditions, such as the temperature and pressure of the emitted gases and the flow rate of emissions.
Rain Gauges: Modern rain gauges often come equipped with wireless communication capabilities, allowing them to transmit data on rainfall amounts to monitoring centers in real time. Stream Gauges: Many stream gauges are designed to wirelessly transmit data on water levels and flow rates, providing crucial information for flood forecasting.Soil Moisture Sensors: These sensors can be equipped with wireless communication to send soil moisture data to a central system, which helps in assessing the risk of flooding, especially in areas prone to flash floods. Pressure Transducers: Used in various water bodies, these sensors can wirelessly transmit water pressure data, which is then used to calculate water levels. Ultrasonic Sensors: These can be set up to measure water levels and then transmit the data wirelessly to a central monitoring system. Anemometers: Modern anemometers can send wind data wirelessly to meteorological centers, contributing to broader weather pattern analysis for flood prediction. Tide Gauges: In coastal areas, tide gauges equipped with wireless communication capabilities transmit sea level data, which is crucial for predicting storm surges and coastal floods.
Seismic sensors used for monitoring of seismic activity in geothermal plants can enhance the safety aspect of power generation. Geothermal power plants are generally located near earthquake-prone zones and the ability to manage such power plants remotely is useful for employee safety. Vibration and temperature sensors are used in turbines and generators to monitor temperatures and detect vibrations.
Vibration sensors such as low-frequency accelerometers are mounted on the casing of the turbine and generator near the bearings and shaft. Water quality sensors (Dissolved Oxygen (DO) Sensor)
Wind Sensors (Anemometers): measure wind speed and direction, key factors in sandstorm formation. By understanding wind patterns, it becomes easier to predict the movement and intensity of sandstorms.
