Body-worn sensors to track the health (heart rate, respirations, EKG, body temperature) and location of responders Additional Body Worn Sensors to detect a bullet impacting an officer’s vest; detect the absence of movement that might indicate a crisis condition. Sensors that will track the amount of air in a firefighters SCBA tank
Depending on the application, different types of cameras are used for surveillance. Visual cameras are used for capturing images during daylight, while a thermal camera may be used for night vision, seeing through smoke or fog, vegetation monitoring, fire and heat detection using infrared patterns, etc. Data may be streamed directly from the UAV via a secure communications channel to a remote central location.
Drones equipped with mobile communication link for C&C between the vehicle and a ground control station
Fiber-optic Distributed Temperature Sensing (DTS) systems and pressure gauges enable critical monitoring during exploration and energy production for Enhanced Geothermal Systems (EGS). These sensors can be used to: – Estimate production potential in or between new wells by measuring the distributed temperature and the point pressure, or pressure measured at the bottom of the well. These measurements allow the calculation of reservoir size, flow resistance between wells (if multiple wells are instrumented), well bore damage caused by drilling, effectiveness of the fracturing operations, and well completion. – Monitor surface and subsurface scale buildup and chemical clean-up. Scale, a mineral residue precipitated from geothermal fluid in response to changes in water pressure and temperature, builds up on pipe walls and will, over time, form a thick, insulating layer that limits flow and may block a pipe. Chemicals are injected into the pipe to remove the accumulated scale. By understanding severity of the scaling, operators can better consider what mitigation options are most suitable as well as minimize the use of expensive chemicals. – Provide permanent monitoring of injector and producer wells to allow identification of the specific zones and fractures that produce fluids. – Perform integrity monitoring for casing and tubing leaks to avoid contaminating ground water and subsurface aquifers.
High definition Video Camera, pop-up / remote production facilities with virtualized edge production software,with wireless bridge to deliver multiple camera signals back for broadcast content delivery.
If a speaker has been installed in the UAV, voice messages from the disaster coordination base can be delivered to disaster victims via the cellular network, while the voice of victims can be picked up using the microphone mounted on the UA, and relayed back to the disaster coordination base.
Rain Gauges: Modern rain gauges often come equipped with wireless communication capabilities, allowing them to transmit data on rainfall amounts to monitoring centers in real time. Stream Gauges: Many stream gauges are designed to wirelessly transmit data on water levels and flow rates, providing crucial information for flood forecasting.Soil Moisture Sensors: These sensors can be equipped with wireless communication to send soil moisture data to a central system, which helps in assessing the risk of flooding, especially in areas prone to flash floods. Pressure Transducers: Used in various water bodies, these sensors can wirelessly transmit water pressure data, which is then used to calculate water levels. Ultrasonic Sensors: These can be set up to measure water levels and then transmit the data wirelessly to a central monitoring system. Anemometers: Modern anemometers can send wind data wirelessly to meteorological centers, contributing to broader weather pattern analysis for flood prediction. Tide Gauges: In coastal areas, tide gauges equipped with wireless communication capabilities transmit sea level data, which is crucial for predicting storm surges and coastal floods.
RFID Readers: E.g., Handheld Typical uses: Warehouses: Tracking assets that are packaged or inside a container Hospitals: Tracking asset locations automatically within a limited distance range
Satellites: Geostationary and polar-orbiting weather satellites are equipped with advanced sensors to monitor wind patterns at high altitudes globally. They are particularly useful for tracking large-scale weather systems and providing data for flight path planning over remote areas like oceans. Satellite sensors that track high-altitude wind speeds can range from those capturing basic wind vector data to more complex imaging systems.
Seismic sensors used for monitoring of seismic activity in geothermal plants can enhance the safety aspect of power generation. Geothermal power plants are generally located near earthquake-prone zones and the ability to manage such power plants remotely is useful for employee safety. Vibration and temperature sensors are used in turbines and generators to monitor temperatures and detect vibrations.
Tag sensors and readers for tracking people, collecting environmental data, equipment tracking, and real-time alerts. RFID transmitter devices are mounted on headlamps belts or badge cards of miners to enable tracking of workers in real-time.
Types of sensors: Remote metering, Cathodic protection, Gas density, Pipeline pressure, Custody transfer flow meters, Fire / Gas / H2S alarms, Tank levels, Tank batteries, Temperature sensors, Control valves, Flow monitoring, Electricity consumption, Structural health & deformation, Air pollution
UAV generally carries a video camera and other sensors such as laser scanner, GNSS, gyroscope,accelerometer, and barometer. Streaming the video and other sensor data to a remote location for instant storage, verification and analysis allows the survey team to gauge whether additional data needs to be collected.
Vibration sensors such as low-frequency accelerometers are mounted on the casing of the turbine and generator near the bearings and shaft. Water quality sensors (Dissolved Oxygen (DO) Sensor)
Wind Sensors (Anemometers): measure wind speed and direction, key factors in sandstorm formation. By understanding wind patterns, it becomes easier to predict the movement and intensity of sandstorms.
