* Temperature & humidity sensors * Volumetric airflow & fluid sensors * Mold sensors * Occupancy detecting sensors * CO2 demand-controlled ventilation (DCV) sensors – work with sensors that detect a building’s occupancy and adjust ventilation accordingly * Light Sensors tied to motorized window treatments can pick up on sunlight and adjust window shading during the course of a day
Fiber-optic Distributed Temperature Sensing (DTS) systems and pressure gauges enable critical monitoring during exploration and energy production for Enhanced Geothermal Systems (EGS). These sensors can be used to: – Estimate production potential in or between new wells by measuring the distributed temperature and the point pressure, or pressure measured at the bottom of the well. These measurements allow the calculation of reservoir size, flow resistance between wells (if multiple wells are instrumented), well bore damage caused by drilling, effectiveness of the fracturing operations, and well completion. – Monitor surface and subsurface scale buildup and chemical clean-up. Scale, a mineral residue precipitated from geothermal fluid in response to changes in water pressure and temperature, builds up on pipe walls and will, over time, form a thick, insulating layer that limits flow and may block a pipe. Chemicals are injected into the pipe to remove the accumulated scale. By understanding severity of the scaling, operators can better consider what mitigation options are most suitable as well as minimize the use of expensive chemicals. – Provide permanent monitoring of injector and producer wells to allow identification of the specific zones and fractures that produce fluids. – Perform integrity monitoring for casing and tubing leaks to avoid contaminating ground water and subsurface aquifers.
For habitat environment observation, monitoring sensors such as temperature, humidity, height, wind, light, and cameras are used
Irradiance, temperature, humidity sensors and voltage sensors used to measure photovoltaic (PV) output current and voltage on solar panels. By placing sensors along the distribution channels and substations operators are able to gather real-time power consummation data which will helps make decisions about the load, voltage, and power being supplied
LED sensors equipped to capture data around ambient light levels, temperature, occupancy, security, performance & energy consumption
Light sensors – allows for the greenhouse lighting to be adjusted depending on the sun’s intensity, benefits of increasing electrical efficiency and cost savings of the entire system. Sensors for Volumetric water content (VWC), Bulk electrical conductivity (ECb), Temperature – Used to monitor soil moisture content
Mobile-enabled IoT sensors, Bluetooth beacons, infrared counters or sensors embedded in the pavement, turnstiles
Pest control sensors on traps that provide accurate information on trap status, whether armed, unarmed, or armed without a catch.
Sanitation devices connected with sensors provide ability to control water flow, paper consumption, air flow for hand drying, and aroma or cleaning chemical sprays on a timer that can be controlled by a single source
Sensors that monitor a building’s air quality (i.e. carbon monoxide and other volatile carbon emission detection)
Smart meters that collect granular real-time data across the water grid, LED light sensors to monitor water levels in tanks, pH sensors, temperature sensors and turbidity sensors in pipelines and storage and distribution tanks, volume sensor
Smart Waste Bin with wireless ultrasonic fill-level sensors and other indicators such as temperature and tilt within waste container
soil moisture sensors – used to assess the water level in the soil temperature and humidity sensors – used to monitor the environment, which had a direct influence on the water level of the soil
The rodent sensors are placed in the high rodent-activity areas for inspection. When rodents pass through the location, infrared sensors trigger notification to all the relevant parties such as owner and pest management service about the rodent activity so that they can decide a plan of action of elimination.
Types of sensors: Remote metering, Cathodic protection, Gas density, Pipeline pressure, Custody transfer flow meters, Fire / Gas / H2S alarms, Tank levels, Tank batteries, Temperature sensors, Control valves, Flow monitoring, Electricity consumption, Structural health & deformation, Air pollution
Vibration sensors such as low-frequency accelerometers are mounted on the casing of the turbine and generator near the bearings and shaft. Water quality sensors (Dissolved Oxygen (DO) Sensor)
Wind Turbine sensors are used to continually assess acceleration, temperature and vibration. Turbine impact sensors – for monitoring avian and bat collisions Turbine vibration sensors – Vibration sensors provide data that enables predictive maintenance, allowing operators to manage assets at a distance – Turbine – Because of variable wind speeds and frequent braking, the load is never consistent on the turbine, causing a lot of wear on the moving parts. Bearings are the biggest culprit in gearbox failure. When bearings fail, it usually leads to other components, such as gearwheels, breaking down, causing a domino effect of failure across the entire apparatus. One of the biggest issues with regard to bearing failure is lubrication starvation. Vibration sensors can help an operator stay ahead of lubrication issues by detecting subtle friction changes -Blade – Wear and tear on rotor blades come from high winds, lightning, ice, and extreme weather conditions that result in blade imbalance. Over time, these factors lead to cracking and fractures along the edges and pitch system failure. Wireless vibration sensors make it feasible to remotely monitor such conditions, alerting operators to impending failure and maintenance needs without physically accessing the site. These sensors are combined together into one communication channel. Associated KPI’s are considered in the aggregate.
Wireless Z-Traps are devices used to catch pests around the plants using pheromone lure. Pest count information is wirelessly passed along from up to 1 km away using a base station to the online cloud service. This information is used to study and determine where and how much pesticides will be required. Imagery sensors capture imagery data to identify the diseases in plants – RGB sensors – have three colour channels, i.e., red, green and blue, which can be used to perceive the biometric effect in the plants – fluorescence Imagery sensors – used to distinguish the photosynthetic activities in the plants – spectral sensors – capture images containing the spatial information of objects in multiple wavebands, used to analyse crops’ health and pest attack – thermal sensors – used to measure the water status in the plant by measuring the temperature Weather condition monitoring sensors, i.e., temperature, dew, humidity and wind speed, are used to monitor weather parameters to find a correlation between pest growth with weather
